Why Do I Get Over 2 Foot-Candle / 20 Lux Visible Light from My LED UV-A Lamp?

Posted By: Steve Published: 09/08/2020 Times Read: 1876

In both the Penetrant and Magnetic Particle checklists, Nadcap requires UV-A lamps to be checked for visible emission at 15 in / 38 cm using a standard light meter. Frequently, readings are above 2 foot-candles / 20 lux, and the conclusion is there’s something wrong with the lamp. However, the process of identifying the root cause is not that simple.

Visible Light Emission Requirement

The requirement for checking visible light emission from UV-A lamps traces back 25-30 years. At the time, there was only one type of inspection lamp – mercury vapor – but there were a couple of different configurations. The standard 100W lamp required a separate “woods glass” filter to block out visible light and only transmit UV-A. By far, this was the most common lamp in use, but it was not the only one available. 125W self-filtered bulbs offered high intensity and the bulb itself was “woods glass” to filter out visible light. The problem was the bulb glass was too thin to block all the visible light. 

The New Requirement

In response, aerospace primes created a new requirement: if you were using a 125W lamp, you had to check the visible light emission to maintain the dark inspection area below 2 foot-candles / 20 lux. A simple solution, but there was some complexity involved – different light meters would give widely different results. That’s because the reading you get from a standard light meter depends on the filters used to tailor its response curve, and different manufacturers use different filter stacks. Typically that variation isn’t a problem when measuring a white light source, but not so with UV-A sources. Inspection lamps are very intense, and the filter stack in the light meter must block all UV energy and only pass the tiny amount of visible light remaining. Optical filters are not 100% effective, so the meter reading depends more on the exact types and tolerances of the filter stack than it does on the source itself. To solve this technical difficulty, aerospace primes included a table of approved light meters and the maximum acceptable reading for each one. The acceptable readings varied widely, from 0.3 to 8 FC or 3 to 86 lux depending on the light meter. 

In time, this aerospace prime requirement was included in Nadcap checklists, but there were a few modifications:

  1. The requirement applied to all UV-A lamps, not just 125W self-filtered lamps. That means that a new quality check was required for a problem that did not exist in all lamps.
  2. The test procedure was changed from a standard 1,200 µW/cm2 lamp intensity to a standard 15 in / 38 cm distance. Originally, the lamp was held at whatever distance was needed to get 1,200 µW/cm2, and then the visible light was checked. Now the lamp is at a fixed distance, meaning higher intensity lamps produce higher readings regardless of the relative light emission.
  3. The table of light meters was not included. All light meters were assumed to have the same response curve, even though that was not true.

Standard 100W mercury vapor lamps produced a very sharp peak at 365 nm, so there were seldom any problems with visible light emission. But LED lamps changed things.

UV-A LEDs have a broader emission spectrum, including a small amount of visible light, which can be observed as a deep violet glare. To eliminate that glare, ASTM E3022 requires that inspection lamps include a UV-A Pass filter to block visible emission. Learn about the function and importance of UV-A pass filters, and why ASTM E3022 requires all LED UV lamps to have them here. Even so, many operators still get readings above 2 FC / 20 lux with their standard light meters, and that continues to be a problem.


Ultimately, the answer is that standard light meters are not able to accurately measure the small visible light emissions from a high-intensity UV-A source. LED lamp manufacturers use spectroradiometers to calculate the visible emissions from each lamp during ASTM E3022 certification. With standard light meters, the filter stacks and tolerances vary from model to model and from manufacturer to manufacturer. That means different light meters give you different readings from the same LED lamp, dependent on each meter’s response curve. While it didn’t make much difference with old mercury vapor lamps, it does make a difference with the broader emission spectrum of UV-A LEDs.

Learn what to consider when looking for a new UV-A light for fluorescent penetrant testing or magnetic particle inspection​ here


Geis, David. "Why Do I Get Over 2 Foot-Candle / 20 Lux Visible Light from My LED UV-A Lamp?" Magnaflux Blog, 26 November 2019, https://www.magnaflux.com/Magnaflux/Resources/Blog/2-Foot-Candle-LED

Tags: non-destructive testing (ndt), magnaflux, magnetic particle inspection (mpi), liquid penetrant inspection (lpi), fluorescent, black, light, uv-a, ultra, violet, foot, candle, lux, visible, led, lamp,

Products related to this post


Starting at $1,155.00

Related Posts